Tone Generator (Hz) & Speaker Test

Runs in your browser · Files stay on your device · 100% private

Generate exact Hz tones and eject water

Active frequency
440 Hz
Stereo channel balance (left / right speaker check)

Tone stopped. Lower headphone volume before testing high frequencies.

Quick frequency presets

About Tone Generator (Hz) & Speaker Test

Online Tone Generator produces accurate audio frequencies from 20 Hz sub-bass up to 20,000 Hz treble directly through your browser Web Audio synthesizer. Dial in any exact frequency with the logarithmic slider or numeric Hz box, choose sine, triangle, square, or sawtooth waves, and isolate the left or right channel to test stereo headphones and speakers. Built-in one-click shortcuts also run a 10-second 165 Hz low-frequency vibration cycle commonly used to help push water droplets out of wet phone speaker grilles, or an 8-second sweep from 20 Hz to 12 kHz.

How to Use Tone Generator (Hz) & Speaker Test

1

Lower volume first, then pick a frequency

Start with system volume moderate. Drag the slider, type an exact Hz value, or click a quick preset such as 165 Hz Water eject or 440 Hz A4 Tuning.

2

Choose waveform and stereo channel

Keep Sine selected for a pure reference tone. Switch between Left only, Center, and Right only to confirm headphone cables and speakers are wired properly.

3

Play a continuous tone, water eject, or sweep

Click Play tone for continuous sound, 165 Hz water eject (10s) for a timed low-frequency vibration pulse, or Sweep 20 Hz to 12 kHz to inspect speaker rattle across the spectrum.

4

Stop playback cleanly

Click Stop tone at any moment. Gain ramps smoothly to zero over a few milliseconds to avoid speaker clicks or pops.

Common Use Cases

Clearing muffled phone speakers after splashes

Hold your phone speaker facing downward and run the 165 Hz water eject preset at high phone volume so air pulses dislodge trapped droplets from the mesh.

Verifying stereo left and right channels

Check whether headphones, soundbars, or studio monitors are swapped or have a dead driver using the Left only and Right only switches.

Tuning instruments and testing speaker rattle

Play a steady 440 Hz A4 reference pitch or sweep low frequencies between 40 Hz and 200 Hz to locate buzzing desk panels and loose speaker enclosures.

Technical Specifications

Input Formats Frequency (20 Hz to 20,000 Hz), Waveform, Stereo pan
Output Formats Live Web Audio synthesis
File Size Limit No strict limit (dependent on device memory)
Processing Engine 100% Client-side (Runs locally in your browser)
Data Retention never uploaded
Batch Processing Single file processing

Tips for Best Results

  • When using the 165 Hz water eject preset on a phone, disconnect Bluetooth earbuds first so the sound plays out of the phone internal speaker.

  • Use Online Voice Recorder or Audio Cutter if you need to record and edit audio tracks.

  • Avoid playing high frequencies above 4,000 Hz at maximum headphone volume.

Frequently Asked Questions

How does the 165 Hz water eject sound work?

A pure 165 Hz sine wave makes small phone speaker cones move at a steady, relatively long excursion, pushing air pulses out through the waterproof mesh to help shake loose surface-tension droplets.

Why can I not hear tones below 30 Hz or above 16,000 Hz?

Most laptop and phone speakers roll off sharply below 80 Hz, and adult human hearing naturally tapers off between 14,000 Hz and 17,000 Hz.

Why does the frequency slider move faster at higher numbers?

Human pitch perception is logarithmic, so a logarithmic slider gives you fine control over bass and musical octaves without cramming 20 Hz to 500 Hz into a few pixels.

Does Tone Generator work offline?

Yes. The oscillator runs entirely inside the browser Web Audio API without downloading external audio clips.

Is it safe for my speakers?

Yes at normal listening volumes. The tool caps internal gain and fades playback in and out cleanly, though you should always avoid maxing out amplifiers on square or sawtooth waves.